DB DRIVE SPEED SERIES A490

We believe that our webpage help you and we will be glad if you visit us in the future. The second set of speaker terminals are intended for ease of connection when running multiple woofers. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Posted 10 hours ago Be the first to answer. Try to keep the length of the cable as short as possible, preferably less than 6″. Adjustable Input Sensitivity Allows you to fine-tune the level matching between your source and the power amplifier. To avoid possibility of induced noise from the car’s electrical system i.

This connection can also be made to the radio’s Power Antenna wire. Run the wire directly to the positive terminal of the car’s battery. Popular Tags type 39 amp. Please click us here: Dos de los lugares sugeridos son la cajuela o debajo del asiento. This will protect the car’s battery in case of a short circuit between the power amplifier and battery. This warranty applies to the original purchase only.

Posted on Feb 06, Be the first to answer. Before you can properly address the problem, you must first find the component that is causing the problem. Make sure you know where they are when mounting the amplifier to avoid puncturing lines, shorting wires or drilling holes in the gas tank.

a40 Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. Once the thermal circuit is activated, the amplifier will shut down to cool off. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself.

Mono Amplifiers | Car Audio: DB DRIVE A4 PRO AMPLIFIER (2 X W @ 4_ 2 X W @ 2_) Review

Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well as a gas tank in the automobile. The amplifier will drivd on and off with the head unit to save current consumption. Also, when using multiple components, make sure all units are grounded at the same point. Listening to rb system at loud levels while driving will impair your ability to hear traffic sounds and emergency vehicles.

  ENVIROSAX GREENGROCER SERIES

Use a grommet to protect the wire when running through the fire wall.

DB Drive A490 Speed Series Amplifiers (90W x 4)

The crossover point should be determined by the speakers operating range. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. To weries warranty service please contact your retailer or see our web site at wwwdbdrive.

Loosen screw terminal and connect bare wire and tighten. This warranty applies to the original purchase only.

Previous speef was receiving ok with coaxial connected but no antennae outside? Page of 17 Go. All products are warranted to be free from defects in material and workmanship under normal use and service for a period of 1 year when the unit is installed by an authorized DB DRIVE dealer.

Posted on Oct 25, Be the first to answer.

If the radio has a REMOTE output terminal, connect it to the amplifier’s terminal marked “remote” using a 16 gauge wire or heavier. All products are warranted to be free from defects in material and workmanship under normal use and service for a period of 1 year when the unit is installed by an autho- rized DB DRIVE dealer.

This connection can also be made to the radio’s Power Antenna wire. Whether adding to an existing system or including your DB Seriew amplifier in a new system, you are certain to notice immediate performance benefits.

Run the wire directly to the positive terminal of the car’s battery.

Andrew Taylor Level 3 Expert Answers. Table of Contents Add to my manuals Add.

Fs: Db Drive 12″ Platinum Sub And Db Drive 4 Channel Amp

This control also operates the reset circuit for the amplifier’s protection. Once you select your mounting location, you will need to run the control wire from the remote to the amplifier. This will send only low frequencies to your subwoofers see example settings below.

Use caution to make sure no stray wire strands come in contact with surrounding terminals causing short circuits. This is spsed a volume control and you will not get more power out of the amplifier in the maximum position! PDF Click to preview. This is one of the most misunderstood adjustments.

  134 MODI PER INNAMORARSI FILM COMPLETO

Dtive make sure that the point on the car where the connection is to be made is free of paint and dirt. Don’t show me this message again.

DB DRIVE SPEED SERIES AMPLIFIER SPA SPAD INSTRUCTION MANUAL Pdf Download.

Connect the amplifier to the car’s battery At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car’s fuse box. Select the location in which you wish to mount the amplifier.

Your selection of a DB Drive car audio product indicates a true appreciation of fine musical reproduction. This manual also for: The Bluetooth has been working fine until a couple of days ago when my device would not connect even though it was working fine before dg. Enter text from picture: Two popular mounting locations are in the trunk or under the seat. Do not run any wires underneath vehicle Exposed wires have a chance of being cut or damaged. Por ejemplo, si usted desea correr un par de subwoofers, puede seleccionar “Low Pass” en el amplificador para filtrar fuera altas frequencia.

It is recommended that you have our product installed by an authorized DB Drive retailer.

Drivee Level 3 Expert Answers. All products are warranted to be free. Use caution when mounting amplifier Remember there are many electrical wires, gas lines, vacuum lines, brake lines as well as a gas tank in the automobile.

This will protect the car’s battery in case of a short circuit between the power amplifier and battery. On this page you can download it for free. Tenga cuidado durante el montaje del amplificador.